VF-AS3 Industrial Inverter — Kode alarm
Kode trip dan alarm ditampilkan pada panel LCD drive (bab 13 pada manual).
| Kode | Alarm |
|---|---|
| E | Emergency off |
| E-11 | Brake answer error |
| E-12 | PG error |
| E-13 | Abnormal speed error |
| E-18 | Analog input disconnecting |
| E-19 | CPU communication error |
| E-20 | Over torque boost |
| E-21 | CPU1 fault B |
| E-22 | Embedded Ethernet fault |
| E-23 | Option fault (slot A) |
| E-24 | Option fault (slot B) |
| E-25 | Option fault (slot C) |
| E-26 | CPU2 fault |
| E-29 | Control power option failure |
| E-31 | Rush current suppression relay fault |
| E-32 | PTC failure |
| E-37 | Servo lock error |
| E-38 | Communication time-out of Braking unit PB7-4132K |
| E-39 | PM control error |
| E-42 | Cooling fan fault |
| E-43 | Communication time-out (embedded Ethernet) |
| E-44 | Battery of panel failure |
| E-45 | GD2 auto-tuning error |
| E-46 | Preparation signal cut during position control |
| E-47 | Position detection upper limit excess |
| E-48 | Braking unit PB7-4132K internal fault |
| E-99 | Trip for test |
| EEP1 | EEPROM fault 1 |
| EEP2 | EEPROM fault 2 |
| EEP3 | EEPROM fault 3 |
| EF2 | Grounding fault |
| EPHI | Input phase loss |
| EPHO | Output phase loss |
| Err2 | RAM fault |
| Err3 | ROM fault |
| Err4 | CPU1 fault A |
| Err5 | Communication time-out (RS485) |
| Err6 | Gate array fault |
| Err7 | Current detector fault |
| Err8 | Communication time-out (option) |
| Err9 | Panel disconnection during run |
| Etn | Auto-tuning error |
| Etn1 | Auto-tuning error 1 |
| Etn2 | Auto-tuning error 2 |
| Etn3 | Auto-tuning error 3 |
| EtyP | Inverter type error |
| OC1 | Overcurrent (during acceleration) |
| OC2 | Overcurrent (during deceleration) |
| OC3 | Overcurrent (during constant speed running) |
| OCA1 | Overcurrent (U-phase arm) |
| OCA2 | Overcurrent (V-phase arm) |
| OCA3 | Overcurrent (W-phase arm) |
| OCL | Overcurrent (load side at startup) |
| OCr | Overcurrent (Braking resistor) |
| OH | Overheat |
| OH2 | External thermal trip |
| OL1 | Overload (Inverter) |
| OL2 | Overload (Motor) |
| OL3 | Overload (IGBT) |
| OLr | Overload (Braking resistor) |
| OP1 | Overvoltage (during acceleration) |
| OP2 | Overvoltage (during deceleration) |
| OP3 | Overvoltage (during constant speed running) |
| Ot | Overtorque |
| Ot2 | Overtorque 2 |
| OtC3 | Overtorque/Overcurrent |
| PrF | STO circuit fault |
| SOUT | PM step-out |
| UC | Undercurrent |
| UP1 | Undervoltage (Power circuit) |
| Ut | Undertorque |
| UtC3 | Undertorque/Undercurrent |
| A-09 | Panel disconnection alarm |
| A-17 | Key failure alarm |
| A-18 | Analog input disconnection alarm |
| A-29 | Control power supply option alarm |
| A-43 | Communication alarm (embedded Ethernet) |
| COFF | Control power option alarm |
| MOFF | Undervoltage alarm |
| PrA | STO activated |
| tUn1 | Brake learning error |
| tUn2 | Light-load high-speed learning setting error |
| tUn3 | Light-load high-speed learning error |