Siemens 6SN1111-0AA01-2FB0
SIMODRIVE 611 HF Commutating Reactor
Lifecycle & replacement
Lifecycle status not indexed
No manufacturer-published lifecycle data for Siemens part numbers is indexed here yet. Ask IAC to check availability and an upgrade path.
IAC stocks legacy spares and exchange units and quotes upgrade paths. Send us the nameplate details and we will confirm a compatible replacement.
Official description
SIEMENS SIMODRIVE 611 FILTER PACKAGE 120 KW,CONTAINS: HF COMMUTATING REACTOR AND MAINS FILTER
Source: Siemens catalog short-text.
Fault codes for this line reactor (96)
- 300007Axis %1 drive %2 not present or inactive
- 300008Axis %1 drive %2 measuring circuit %3 is not available
- 300009Axis %1 drive %2 measuring circuit %3 wrong measuring circuit type (type %4 used)
- 300010Axis %1 drive %2 active without NC axis assignment
- 300011Axis %1 drive %2 hardware version of spindle not supported
- 300012Axis %1 drive %2 hardware version of control module not supported
- 300020Drive %1 removed for diagnostics
- 300100Drive power failure
- 300101Bus communications failure
- 300200Drive bus hardware fault
- 300201Axis %1 drive %2 timeout during access, error location %3
- 300202Axis %1 drive %2 CRC error, error location %3
- 300300Axis %1 drive %2 boot error, error code %3
- 300400Axis %1 drive %2 system error, error codes %3, %4
- 300401Drive software for type %1, block %2 missing or incorrect
- 300402System error in drive link. Error codes %1, %2
- 300403Axis %1 drive %2 drive software and drive MD with different version numbers
- 300404Axis %1 drive %2 drive MD contains different drive number
- 300405Axis %1 drive %2 unknown drive alarm, code %3
- 300406Problem in the non-cyclic communication for basic address %1, additional information %2, %3, %4
- 300410Axis %1 drive %2 error when storing a file (%3, %4)
- 300411Axis %1 drive %2 error when reading a file (%3, %4)
- 300412Error when storing a file (%1, %2)
- 300413Error when reading a file (%1, %2)
- 300423Measuring results could not be read (%1)
- 300500Axis %1 drive %2 system error, error codes %3, %4
- 300501Axis %1 drive %2 maximum current monitoring
- 300502Axis %1 drive %2 maximum current monitoring of phase current R
- 300503Axis %1 drive %2 maximum current monitoring of phase current S
- 300706Axis %1 drive %2 monitoring cycle time invalid
- 300707Axis %1 drive %2 basic cycle times of axes differ
- 300708Axis %1 drive %2 current controller cycle times of axes differ
- 300709Axis %1 drive %2 speed controller cycle times of axes differ
- 300710Axis %1 drive %2 position controller cycle times of axes differ
- 300711Axis %1 drive %2 monitoring cycle times of axes differ
- 300712Axis %1 drive %2 configuration of controller structure (higher dynamic response) not possible
- 300713Axis %1 drive %2 lead time for position controller invalid
- 300714Axis %1 drive %2 power section code invalid
- 300715Axis %1 drive %2 maximum power section current less than or equal to zero
- 300716Axis %1 drive %2 torque constant less than or equal to zero
- 300717Axis %1 drive %2 motor moment of inertia less than or equal to zero
- 300718Axis %1 drive %2 calculation dead time of current controller less than or equal to zero
- 300719Axis %1 drive %2 motor not parameterized for delta operation
- 300720Axis %1 drive %2 maximum motor speed invalid
- 300721Axis %1 drive %2 zero-load current greater than rated motor current
- 300722Axis %1 drive %2 zero-load motor current greater than rated current of power section
- 300723Axis %1 drive %2 STS configuration of axes differ
- 300724Axis %1 drive %2 number of pole pairs invalid
- 300737Axis %1 drive %2 configuration of two EnDat encoders not possible
- 300738Axis %1 drive %2 module number for measuring system not possible
- 300739Axis %1 drive %2 measuring system already used as motor measuring system
- 300740Axis %1 drive %2 measuring system used several times
- 300741Axis %1 drive %2 asynchronous mode: feedforward control gain out of range
- 300742Axis %1 drive %2 voltage/frequency mode: converter frequency invalid
- 300743Axis %1 drive %2 function not supported on this 611D controller module
- 300744Axis %1 drive %2 safety monitoring checksum invalid, confirmation and acceptance test required!
- 300745Axis %1 drive %2 limit values for safe end positions exchanged
- 300746Axis %1 drive %2 SBH/SG not enabled
- 300747Axis %1 drive %2 monitoring cycle time MD 1300 invalid
- 300788Axis %1 drive %2 parameterization error in current control adaption
Reference manuals (hosted by IAC)
Get a quote for a replacement
Industrial Automation Co. stocks, sources, and repairs Siemens parts — new, refurbished, or exchange units with warranty.
Reference information compiled from official Siemens documentation; always confirm against the manual for your exact unit and firmware.