B&R 8B0C0320HW00.B00-1
ACOPOSmulti auxiliary supply module, 35 A, AS, wall mounting, 42...58 VOut
Lifecycle & replacement
Lifecycle status not indexed
No manufacturer-published lifecycle data for B&R part numbers is indexed here yet. Ask IAC to check availability and an upgrade path.
Replacing or upgrading a servo component?
Servo amplifiers, motors, encoders and cables are matched sets. If this part is no longer available in its original form, the manufacturer's newer generation usually will not pair with the rest of the axis, so an upgrade normally covers the drive, motor and cables together. Send us the nameplate details and we will confirm availability of an exact spare or scope a compatible upgrade.
IAC stocks legacy spares and exchange units and quotes upgrade paths. Send us the nameplate details and we will confirm a compatible replacement.
Technical specifications
General information
| Certifications / CE | Yes |
| Certifications / UKCA | Yes |
| Certifications / CRA (Cyber Resilience Act) | In preparation |
| Certifications / UL | cULus E225616 Power conversion equipment |
| Cooling and mounting type | Wall mounting |
DC bus connection
| Voltage / Nominal | 750 VDC |
| Voltage / Operating range in continuous operation | 260 to 800 VDC |
| Voltage / Full continuous power | 550 to 800 VDC |
| Continuous power consumption | Max. 2120 W |
| Power dissipation with continuous power | 15 W (0% continuous power) 30 W (50% continuous power) 90 W (100% continuous power) |
| DC bus capacitance | 1.2 µF |
| Variant | ACOPOSmulti backplane |
24 VDC output
| Output voltage / DC bus voltage (UDC): 260 to 315 VDC | 25 VDC * (UDC/315) |
| Output voltage / DC bus voltage (UDC): 315 to 800 VDC | 24 VDC ±6% |
| Variant / 24 VDC, COM | Connector |
| Quantity | 1 |
| Fuse protection | 250 mA (slow-blow) electronic, automatic reset |
24 VDC internal system power supply
| Input voltage | 25 VDC ±1.6% |
| Input capacitance | 47 µF |
| Max. power consumption | 7 W + P 24 VDC Out |
| Variant | ACOPOSmulti backplane |
58 VDC output
| Output voltage / Nominal | 58 VDC |
| Output voltage / Workspace | 42 to 58 VDC |
| Output voltage / Residual ripple | Typ. 200 mVSS |
| Output voltage / Input stability | Typ. <50 mV (dynamic) |
| Output voltage / Load stability | 250 mVSS (dynamic) |
| Reduction of continuous current / Depending on ambient temperature | 0.2 A/K (starting at 40°C) |
| Reduction of continuous current / Depending on installation elevation | 3.5 A per 1000 m (starting at 500 m above sea level) |
| Reduction of continuous current / Depending on the input voltage | 0.0732 A/V * (550 V - Input voltage) |
| Reduction of continuous current / Depending on cooling type | No reduction |
| Reduction of peak current / Depending on the input voltage | 0,136 A/V * (600 V - Input voltage) |
| Protective measures / No-load proof | Yes |
| Protective measures / Overload-proof | Yes |
| Protective measures / Short-circuit proof | Yes |
| Protective measures / Feedback protection | Yes <63 V |
| Protective measures / Overtemperature protection | Yes |
| Protective measures / Output/Input isolation | PELV |
| Quantity | 1 |
| Continuous power | (Output voltage / 58 VDC) * 2030 W |
| Continuous current | ±35 A |
| Peak current | ±60 A (max. 2 s) |
| Startup delay | Max. 8 s |
| Startup time | Typ. 300 ms |
| Variant | Connector |
| Shield connection | Yes |
| Connection | Parallel connection on output: Not permitted Serial connection on output: Not permitted |
| Max. cable length | 30 m |
Fieldbus
| Type | POWERLINK V2 controlled node (CN) |
| Variant | 2x RJ45, shielded, 2-port hub |
| Line length | Max. 100 m between 2 stations (segment length) |
| Transfer rate | 100 Mbit/s |
Digital inputs
| Input voltage / Nominal | 24 VDC |
| Input voltage / Maximum | 30 VDC |
| Switching delay / Rising edge | 52 ±0.5 µs (digitally filtered) |
| Switching delay / Falling edge | 53 ±0.5 µs (digitally filtered) |
| Quantity | 1 |
| Modulation compared to ground potential | ±38 VDC |
| Circuit | Sink |
| Input current at nominal voltage | Typ. 10 mA |
| Switching threshold | LOW: <5 VDC HIGH: >15 VDC |
| Electrical isolation | Yes |
| Shielding | No |
| Max. cable length | 30 m |
Signal loop through
| Quantity | 2 pairs |
| Voltage | Max. 30 VDC |
| Current | Max. 100 mA |
| Electrical isolation | Yes |
| Loop through for STO | Yes |
| Shielding | No |
| Variant | Pair1_1, Pair1_2, Pair2_1, Pair2_2 |
| Max. cable length | 30 m |
Battery voltage measurement
| Input voltage / Maximum | 10 V |
| Measurement / Load pulse | 3 mA |
| Measurement / Pulse duration | Max. 500 ms |
| Measurement / Threshold value for undervoltage warning | 5.2 V |
| Quantity | 1 |
| Electrical isolation | Yes |
| Idle current | Max. 10 µA |
| Variant | Connector |
| Shielding | No |
| Max. cable length | 30 m |
Support
| Motion system / mapp Motion | 5.13.1 and higher |
| Motion system / ACP10/ARNC0 | All versions |
Operating conditions
| Permissible mounting orientations / Hanging vertically | Yes |
| Permissible mounting orientations / Horizontal, face up | Yes |
| Permissible mounting orientations / Standing horizontally | No |
| Installation elevation above sea level / Nominal | 0 to 500 m |
| Installation elevation above sea level / Maximum | 4000 m |
| Pollution degree per EN 61800-5-1 | 2 (non-conductive pollution) |
| Overvoltage category per EN 61800-5-1 | III |
| Degree of protection per EN 60529 | IP20 |
Ambient conditions
| Temperature / Operation / Nominal | 5 to 40°C |
| Temperature / Operation / Maximum | 55°C |
| Temperature / Storage | -25 to 55°C |
| Temperature / Transport | -25 to 70°C |
| Relative humidity / Operation | 5 to 85% |
| Relative humidity / Storage | 5 to 95% |
| Relative humidity / Transport | Max. 95% at 40°C |
Mechanical properties
| Dimensions / Depth / Wall mounting | 263 mm |
| Dimensions / Width | 53.5 mm |
| Dimensions / Height | 317 mm |
| Weight | 3.2 kg |
| Module width | 1 |
Documentation & CAD
Files hosted by B&R Industrial Automation; links open the official download page.
Datasheets
Manuals
3D CAD models
ECAD / EPLAN
Get a quote for a replacement
Industrial Automation Co. stocks, sources, and repairs B&R parts — new, refurbished, or exchange units with warranty.
Specifications from the official B&R product catalog. Always confirm against the datasheet for your exact revision.