B&R X90DSI00.04-00
18 to 30 VDC 4 IO-Link devices 4 digital channels, can be used as inputs or outputs Sensor/actuator power supply NetTime timestamps: IO-Link data X2X Link The DS option board is an IO-Link master that allows intelligent sensors and actuators to be connected per the IO-Link standard. Communication to the mainboard is made possible via X2X Link.
Lifecycle & replacement
No manufacturer-published lifecycle data for B&R part numbers is indexed here yet. Ask IAC to check availability and an upgrade path.
IAC stocks legacy spares and exchange units and quotes upgrade paths. Send us the nameplate details and we will confirm a compatible replacement.
Technical specifications
Short description
| I/O module | IO-Link master with 4 IO-Link interfaces |
General information
| Diagnostics / Module run/error | Yes, using software status |
| Power consumption / Internal I/O | 0.6 W |
| Certifications / CE | Yes |
| Certifications / UKCA | Yes |
| Certifications / CRA (Cyber Resilience Act) | In preparation |
| B&R ID code | 0xF9F7 |
| Status indicators | - |
| Additional power dissipation caused by actuators (resistive) [W] | - |
Sensor/Actuator power supply
| Overload protection / Switch-off delay | Configurable using software |
| Overload protection / Switch-off duration | Configurable using software |
| Voltage | I/O power supply minus voltage drop for short-circuit protection |
| Voltage drop for short-circuit protection at 0.3 A | Max. 0.3 V |
| Power consumption | Max. 12 W per IO-Link interface |
| Short-circuit proof | Yes |
IO-Link in master mode
| Transfer rates / COM1 | 4.8 kbaud |
| Transfer rates / COM2 | 38.4 kbaud |
| Transfer rates / COM3 | 230.4 kbaud |
| Limit values for COM3 / Max. connection capacity | 22 nF (cable + IO-Link device) |
| Limit values for COM3 / Max. load | 96 Ω / 250 mA |
| Data format | 1 start bit, 8 data bits, 1 parity bit (even), 1 stop bit |
| Bus level | 24 VDC (active), 0 VDC (resting voltage) |
IO-Link in master mode or in SIO mode "digital output"
| Switching delay / 0 → 1 | <1 µs |
| Switching delay / 1 → 0 | <1 µs |
| Variant | Bipolar, positive and negative switching |
| Peak short-circuit current | <1.3 A |
| Residual voltage | <0.7 VDC at nominal current 0.25 A |
| Switching voltage | I/O power supply minus voltage drop for short-circuit protection and semiconductor switch |
| Voltage drop on semiconductor switch | Max. 0.44 VDC at 0.2 A |
| Switching frequency | Typ. 25 kHz 300 kHz in IO-Link master mode |
| Switch-on in the event of overload shutdown or short-circuit shutdown | Configurable with software |
IO-Link in SIO mode "Digital output"
| Nominal voltage | 24 VDC |
| Nominal output current | 0.25 A |
| Total nominal current | Max. 1 A |
| Output circuit | Sink or source |
| Switching frequency (resistive load) | Max. 500 Hz |
| Output protection | Thermal shutdown in the event of overcurrent or short circuit, integrated protection for switching inductive loads |
IO-Link in SIO mode "digital input"
| Input filter / Hardware | 220 ns |
| Input filter / Software | 3 µs (without glitch filter) 4.2 µs (with glitch filter) |
| Switching threshold / Low | <5 VDC |
| Switching threshold / High | >15 VDC |
| Nominal voltage | 24 VDC |
| Input characteristics per EN 61131-2 | Type 1 |
| Input circuit | Sink |
| Input voltage | 24 VDC -15% / +20% |
| Input current at 24 VDC | Typ. 5.8 mA |
| Input resistance | Typ. 4.14 kΩ |
Electrical properties
| Electrical isolation | Bus isolated from IO-Link IO-Link not isolated from IO-Link |
Operating conditions
| Mounting orientation / Any | Yes |
| Degree of protection per EN 60529 | Up to IP69K |
Ambient conditions
| Temperature / Storage | -40 to 85°C |
| Temperature / Transport | -40 to 85°C |
| Relative humidity / Operation | 5 to 100%, condensing |
| Relative humidity / Storage | 5 to 100%, condensing |
| Relative humidity / Transport | 5 to 100%, condensing |
Mechanical properties
| Dimensions / Width | 47 mm |
| Dimensions / Length | 95 mm |
Documentation & CAD
Files hosted by B&R Industrial Automation; links open the official download page.
Datasheets
Manuals
Get a quote for a replacement
Industrial Automation Co. stocks, sources, and repairs B&R parts — new, refurbished, or exchange units with warranty.
Specifications from the official B&R product catalog. Always confirm against the datasheet for your exact revision.