IAC

SIMODRIVE 611 digital Drive System — Kode alarm

Kegagalan drive SIMODRIVE 611 digital dilaporkan sebagai alarm 6 digit (300000-301799) pada layar CNC SINUMERIK (Diagnosis -> Alarms); nomor axis/drive muncul pada parameter teks alarm.

Berlaku untuk nomor komponen berikut: 6SN1118… (SIMODRIVE 611 Control Unit), 6SN1123… (SIMODRIVE 611 Power Module), 1FT6105… (SIMOTICS S 1FT6 Synchronous Servo Motor), 1FT6086… (SIMOTICS S 1FT6 Synchronous Servo Motor (27 Nm, EnDat Encoder)), 1FT6064… (SIMOTICS S 1FT6 Synchronous Servo Motor (9.5 Nm, 3000 rpm)), 6SN1111… (SIMODRIVE 611 HF Commutating Reactor), 1FT6044… (SIMOTICS S 1FT6 Synchronous Servo Motor (5.0 Nm, 3000 rpm)), 1FT6082… (SIMOTICS S 1FT6 Synchronous Servo Motor (13 Nm))

Manual referensi (bahasa Inggris): 6FC5298-7AA20-0BP3 — Siemens SINUMERIK 840D/810D & SIMODRIVE 611 digital Diagnostics Manual (11/2006)

KodeAlarm
300007Axis %1 drive %2 not present or inactive
300008Axis %1 drive %2 measuring circuit %3 is not available
300009Axis %1 drive %2 measuring circuit %3 wrong measuring circuit type (type %4 used)
300010Axis %1 drive %2 active without NC axis assignment
300011Axis %1 drive %2 hardware version of spindle not supported
300012Axis %1 drive %2 hardware version of control module not supported
300020Drive %1 removed for diagnostics
300100Drive power failure
300101Bus communications failure
300200Drive bus hardware fault
300201Axis %1 drive %2 timeout during access, error location %3
300202Axis %1 drive %2 CRC error, error location %3
300300Axis %1 drive %2 boot error, error code %3
300400Axis %1 drive %2 system error, error codes %3, %4
300401Drive software for type %1, block %2 missing or incorrect
300402System error in drive link. Error codes %1, %2
300403Axis %1 drive %2 drive software and drive MD with different version numbers
300404Axis %1 drive %2 drive MD contains different drive number
300405Axis %1 drive %2 unknown drive alarm, code %3
300406Problem in the non-cyclic communication for basic address %1, additional information %2, %3, %4
300410Axis %1 drive %2 error when storing a file (%3, %4)
300411Axis %1 drive %2 error when reading a file (%3, %4)
300412Error when storing a file (%1, %2)
300413Error when reading a file (%1, %2)
300423Measuring results could not be read (%1)
300500Axis %1 drive %2 system error, error codes %3, %4
300501Axis %1 drive %2 maximum current monitoring
300502Axis %1 drive %2 maximum current monitoring of phase current R
300503Axis %1 drive %2 maximum current monitoring of phase current S
300706Axis %1 drive %2 monitoring cycle time invalid
300707Axis %1 drive %2 basic cycle times of axes differ
300708Axis %1 drive %2 current controller cycle times of axes differ
300709Axis %1 drive %2 speed controller cycle times of axes differ
300710Axis %1 drive %2 position controller cycle times of axes differ
300711Axis %1 drive %2 monitoring cycle times of axes differ
300712Axis %1 drive %2 configuration of controller structure (higher dynamic response) not possible
300713Axis %1 drive %2 lead time for position controller invalid
300714Axis %1 drive %2 power section code invalid
300715Axis %1 drive %2 maximum power section current less than or equal to zero
300716Axis %1 drive %2 torque constant less than or equal to zero
300717Axis %1 drive %2 motor moment of inertia less than or equal to zero
300718Axis %1 drive %2 calculation dead time of current controller less than or equal to zero
300719Axis %1 drive %2 motor not parameterized for delta operation
300720Axis %1 drive %2 maximum motor speed invalid
300721Axis %1 drive %2 zero-load current greater than rated motor current
300722Axis %1 drive %2 zero-load motor current greater than rated current of power section
300723Axis %1 drive %2 STS configuration of axes differ
300724Axis %1 drive %2 number of pole pairs invalid
300737Axis %1 drive %2 configuration of two EnDat encoders not possible
300738Axis %1 drive %2 module number for measuring system not possible
300739Axis %1 drive %2 measuring system already used as motor measuring system
300740Axis %1 drive %2 measuring system used several times
300741Axis %1 drive %2 asynchronous mode: feedforward control gain out of range
300742Axis %1 drive %2 voltage/frequency mode: converter frequency invalid
300743Axis %1 drive %2 function not supported on this 611D controller module
300744Axis %1 drive %2 safety monitoring checksum invalid, confirmation and acceptance test required!
300745Axis %1 drive %2 limit values for safe end positions exchanged
300746Axis %1 drive %2 SBH/SG not enabled
300747Axis %1 drive %2 monitoring cycle time MD 1300 invalid
300788Axis %1 drive %2 parameterization error in current control adaption
300789Axis %1 drive %2 function not supported on this 611D controller module
300790Axis %1, drive %2 Changeover speed/velocity too small
300799Axis %1 drive %2 data backup and reboot required
300850Axis %1 drive %2 parameterization error in speed control adaption
300854Axis %1 drive %2 signal number of var. signaling function invalid
300855Axis %1 drive %2 voltage/frequency mode: motor is turning
300858Axis %1 drive %2 generator mode: response voltage > switch-off threshold
300859Axis %1 drive %2 generator mode: response voltage > monitoring threshold
300860Axis %1 drive %2 generator mode: emergency retraction speed > max. motor speed
300861Axis %1 drive %2 generator mode : minimum axis speed > max. motor speed
300862Axis %1 drive %2 emergency retraction mode/generator mode already active
300863Axis %1 drive %2 emergency retraction mode/generator mode invalid
300864Axis %1 drive %2 emergency retraction mode/generator mode not possible
300865Axis %1 drive %2 measurement of DC link voltage not possible
300875Axis %1 drive %2 fixed link voltage of axes differ
300888Axis %1 drive %2 parameterization error in current control adaption
300950Axis %1 drive %2 is not safely referenced
300951Axis %1 drive %2 test stop is running
300952Axis %1 drive %2 acceptance test is active
301701Axis %1 drive %2 limit value for safe velocity too large
301702Axis %1 drive %2 track inversion incorrect
301703Axis %1 drive %2 encoder/motor type are not compatible
301704Axis %1 drive %2 pole pair width/division of linear scale (internal) out of range
301705Axis %1 drive %2 distance-coded scale incorrectly parameterized
301706Axis %1 drive %2 parameterization of cam position invalid
301707Axis %1 drive %2 parameterization of modulo value for safe cam (SN) invalid
301708Axis %1 drive %2 actual value synchronisation not allowed
301709Axis %1 drive %2 submodule with integrated linearization invalid
301710Axis %1 drive %2 resolution SSI motor measuring system invalid
301711Axis %1 drive %2 transmission length SSI motor measuring system invalid
301712Axis %1 drive %2 multiturn SSI motor measuring system invalid
301713Axis %1 drive %2 resolution SSI direct measuring system invalid
301714Axis %1 drive %2 transmission length SSI direct measuring system invalid
301715Axis %1 drive %2 multiturn SSI direct measuring system invalid
301716Axis %1 drive %2 SSI direct measuring system without incremental signals not possible
301717Axis %1 drive %2 SSI transmission timeout